 |
|||
 |
EN50288-7 Cables |  |
|
|
|||
| XLPE Insulated, LSZH Sheathed Instrumentation Cables |
EN 50288-7 Cables
APPLICATION:
EN 50228-7 cables are used for transmission of analoge and digital signals in instrument and control systems at
chemistry and petr°Chemistry industry plants, power plants, natural gas and petroluem plants, etc... EN 50228-
7 cables are used in the environments which have no corrosive gases are emitted in the event of fire. In case of
fire,EN 50228-7 cables inhibit the propagation of the flames whereby the development of smoke is extremely
low. EN 50228-7 Instrumentation cables are not allowed for direct connection to a low impedance sources, e.g.
public mains electricity supply. With blue sheath it is suitable for intrinsically safe systems.EN 50228-7 cables are
not recommended for direct burial. They are for indoor and outdoor installation, in dry and wet l°Cations; on
racks, trays, in conduits.
STANDARDS
Basic design to EN50288-7
FIRE PERFORMANCE
| Flame Retardance (Single Vertical Wire Test) | EN 60332-1-2; IEC 60332-1-2; BS EN 60332-1-2; VDE 0482-332-1; NBN C 30-004 (cat. F1); NF C32-070-2.1(C2); CEI 20-35/1-2; EN 50265-2-1*; DIN VDE 0482-265-2-1* |
|---|---|
| Reduced Fire Propagation(Vertically-mounted bundled wires & cable test) | EN 60332-3-24 (cat. C); IEC 60332-3-24; BS EN 60332-3-24; VDE 0482-332-3; NBN C 30-004 (cat. F2); NF C32-070-2.2(C1); CEI 20-22/3-4; EN 50266-2-4*; DIN VDE 0482-266-2-4 |
| Halogen Free | IEC 60754-1; EN 50267-2-1; DIN VDE 0482-267-2-1; CEI 20-37/2-1 ; BS 6425-1* |
| No Corrosive Gas Emission | IEC 60754-2; EN 50267-2-2; DIN VDE 0482-267-2-2; CEI 20-37/2-2 ; BS 6425-2* |
| Minimum Smoke Emission | IEC 61034-1&2; EN 61034 -1&2; DIN VDE 0482-1034-1&2; CEI 20-37/3-1&2; EN 50268-1&2*; BS 7622-1&2* |
| No Toxic gases | NES 02-713; NF C 20-454 |
| Sunlight Resistance | UL 1581 section 1200 |
| Oil Resistance | ICEA S-73-532** |
Note: Asterisk * denotes superseded standard, **Test temperature +60°C, duration 4h. Retention: min 60% of tensite strength/min.60% of elongation.
VOLTAGE RATING
300V
CABLE CONSTRUCTION
Conductor: Annealed copper solid or plain copper stranded to IEC 60228 Class 2.
Insulation: PE compound, EN 50290. 2-23.
Individual Screen: Aluminium/polyester tape is applied over each pair metallic side down in contact with tinned
copper drain wire, 0.5mm²
Triple: Three conductors twisted to form a triple
**TiMF Construction: Polyester tape above the triple, AL-PES tape over solid tinned copper drain wire, 0,60 mm
Lay-up: TiMF laid up in layers of optimum pitch
Separator: Polyester tape
Overall Screen: Aluminium/polyester tape with tinned copper drain wire, 0.5mm2
Outer Sheath: Thermoplastic LSZH compound type LTS3 as per BS 7655-6.1 (Thermosetting LSZH compound
type SW2-SW4 as per BS 7655-2.6 can be offered.). UV resistance, hydrocarbon resistance, oil resistance, anti
rodent and anti termite properties can be offered as option.
COLOUR CODE
Insulation: Black / White / Red, continuously numbered on white core(1, 2..)for multitriples.
Outer Sheath: Black or blue for intrinsically safe systems
Physical AND THERMAL PROPERTIES
Temperature Range During Operation (Fixed State): -30°C – +70°C
Temperature Range During Installation (Mobile State): -5°C – +50°C
Minimum Bending Radius: 7.5 X Overall Diameter
Electrical PROPERTIES
| Conductor Area Size | mm 2 | 0.5 | 0.75 | 1.0 | 1.3 | 1.5 | |
|---|---|---|---|---|---|---|---|
| Insulation thickness (nominal) | mm | 0.35 | 0.38 | 0.4 | 0.45 | 0.45 | |
| Conductor resistance (20°C) | Ω/km | 36.7 | 25 | 18.5 | 14.2 | 12.3 | |
| Insulation resistance (20°C) | MΩ.km(Min.) | 5000 | |||||
| Mutual Capacitance (1 kHz) | pF/m(Max.) | 115 | |||||
| Capacitance unbalance(1 kHz) | pF/500 m (Max.) | 500 | |||||
| Inductance | mH/km(Max.) | 1 | 1 | 1 | 1 | 1 | |
| L / R (ratio) (max.) | μH/Ω | 25 | 25 | 25 | 40 | 40 | |
| Operating voltage Urms | V | 300 | |||||
| Test Voltage | Core to Core | V | 1500 | ||||
| Core to Screen | V | 1500 | |||||
CONSTRUCTION PARAMETERS
Caledonian Cable Code |
RE-2Y(St)H-TiMF |
||
|---|---|---|---|
No. of Triples x3xCross Section |
Nominal Insulation Thickness |
Nominal Outer Sheath Thickness |
|
|
No.x3xmm2 |
mm |
mm |
0.5mm2 , Multitriple |
|||
RE-2Y(St)H-TiMF 2T0.5 |
2x3x0.5 |
0.35 |
1.0 |
RE-2Y(St)H-TiMF 4T0.5 |
4x3x0.5 |
0.35 |
1.0 |
RE-2Y(St)H-TiMF 5T0.5 |
5x3x0.5 |
0.35 |
1.1 |
RE-2Y(St)H-TiMF 6T0.5 |
6x3x0.5 |
0.35 |
1.1 |
RE-2Y(St)H-TiMF 8T0.5 |
8x3x0.5 |
0.35 |
1.1 |
RE-2Y(St)H-TiMF 10T0.5 |
10x3x0.5 |
0.35 |
1.2 |
RE-2Y(St)H-TiMF 12T0.5 |
12x3x0.5 |
0.35 |
1.2 |
RE-2Y(St)H-TiMF 16T0.5 |
16x3x0.5 |
0.35 |
1.3 |
RE-2Y(St)H-TiMF 20T0.5 |
20x3x0.5 |
0.35 |
1.4 |
RE-2Y(St)H-TiMF 24T0.5 |
24x3x0.5 |
0.35 |
1.5 |
0.75mm2 , Multitriple |
|||
RE-2Y(St)H-TiMF 2T0.75 |
2x3x0.75 |
0.38 |
1.0 |
RE-2Y(St)H-TiMF 4T0.75 |
4x3x0.75 |
0.38 |
1.1 |
RE-2Y(St)H-TiMF 5T0.75 |
5x3x0.75 |
0.38 |
1.1 |
RE-2Y(St)H-TiMF 6T0.75 |
6x3x0.75 |
0.38 |
1.1 |
RE-2Y(St)H-TiMF 8T0.75 |
8x3x0.75 |
0.38 |
1.2 |
RE-2Y(St)H-TiMF 10T0.75 |
10x3x0.75 |
0.38 |
1.3 |
RE-2Y(St)H-TiMF 12T0.75 |
12x3x0.75 |
0.38 |
1.3 |
RE-2Y(St)H-TiMF 16T0.75 |
16x3x0.75 |
0.38 |
1.4 |
RE-2Y(St)H-TiMF 20T0.75 |
20x3x0.75 |
0.38 |
1.5 |
RE-2Y(St)H-TiMF 24T0.75 |
24x3x0.75 |
0.38 |
1.6 |
RE-2Y(St)H-TiMF 2T1.0 |
2x3x1.0 |
0.4 |
1.0 |
RE-2Y(St)H-TiMF 4T1.0 |
4x3x1.0 |
0.4 |
1.1 |
RE-2Y(St)H-TiMF 5T1.0 |
5x3x1.0 |
0.4 |
1.1 |
RE-2Y(St)H-TiMF 6T1.0 |
6x3x1.0 |
0.4 |
1.2 |
RE-2Y(St)H-TiMF 8T1.0 |
8x3x1.0 |
0.4 |
1.2 |
RE-2Y(St)H-TiMF 10T1.0 |
10x3x1.0 |
0.4 |
1.3 |
RE-2Y(St)H-TiMF 12T1.0 |
12x3x1.0 |
0.4 |
1.3 |
RE-2Y(St)H-TiMF 16T1.0 |
16x3x1.0 |
0.4 |
1.4 |
RE-2Y(St)H-TiMF 20T1.0 |
20x3x1.0 |
0.4 |
1.5 |
RE-2Y(St)H-TiMF 24T1.0 |
24x3x1.0 |
0.4 |
1.6 |
1.3mm2 , Multitriple |
|||
RE-2Y(St)H-TiMF 2T1.3 |
2x3x1.3 |
0.45 |
1.1 |
RE-2Y(St)H-TiMF 4T1.3 |
4x3x1.3 |
0.45 |
1.1 |
RE-2Y(St)H-TiMF 5T1.3 |
5x3x1.3 |
0.45 |
1.2 |
RE-2Y(St)H-TiMF 6T1.3 |
6x3x1.3 |
0.45 |
1.3 |
RE-2Y(St)H-TiMF 8T1.3 |
8x3x1.3 |
0.45 |
1.3 |
RE-2Y(St)H-TiMF 10T1.3 |
10x3x1.3 |
0.45 |
1.4 |
RE-2Y(St)H-TiMF 12T1.3 |
12x3x1.3 |
0.45 |
1.5 |
RE-2Y(St)H-TiMF 16T1.3 |
16x3x1.3 |
0.45 |
1.6 |
RE-2Y(St)H-TiMF 20T1.3 |
20x3x1.3 |
0.45 |
1.7 |
RE-2Y(St)H-TiMF 24T1.3 |
24x3x1.3 |
0.45 |
1.8 |
1.5mm2 , Multitriple |
|||
RE-2Y(St)H-TiMF 2T1.5 |
2x3x1.5 |
0.45 |
1.1 |
RE-2Y(St)H-TiMF 4T1.5 |
4x3x1.5 |
0.45 |
1.2 |
RE-2Y(St)H-TiMF 5T1.5 |
5x3x1.5 |
0.45 |
1.2 |
RE-2Y(St)H-TiMF 6T1.5 |
6x3x1.5 |
0.45 |
1.3 |
RE-2Y(St)H-TiMF 8T1.5 |
8x3x1.5 |
0.45 |
1.4 |
RE-2Y(St)H-TiMF 10T1.5 |
10x3x1.5 |
0.45 |
1.5 |
RE-2Y(St)H-TiMF 12T1.5 |
12x3x1.5 |
0.45 |
1.5 |
RE-2Y(St)H-TiMF 16T1.5 |
16x3x1.5 |
0.45 |
1.6 |
RE-2Y(St)H-TiMF 20T1.5 |
20x3x1.5 |
0.45 |
1.7 |
RE-2Y(St)H-TiMF 24T1.5 |
24x3x1.5 |
0.45 |
1.8 |
Note : Other conductor sizes & core configurations are available upon request.