Cables & Wires

A|B|C|D|E|F|G|H|I|J|K|L|M|N|O|P|Q|R|S|T|U|V|W|X

A

A - Common abbreviation for ampere.

Abrasion Resistance - ability of material or cable to resist surface wear.

AC - Alternating Current (See alternating current).

Accelerated Aging - A test performed on material or cable meant to duplicate longtime environmental conditions

in a relatively short amount of time.

Back to top
...................................................................................................................................................................
B

B+S - Brown and Sharpe wire gauge, same as AWG.

Bare Conductor - A conductor having no insulation or jacket.

.Back to top
...................................................................................................................................................................
C

C Symbol - Designated for: capacitance, bias supply and centigrade.

Cable - An insulated conductor or twisted group of conductors used for the transmission of electrical energy.

Cable Core - The portion of a cable lying under the outer protective covering.

Cable Jacket - See Sheath

Cable Sheath - See Sheath

Cabling - The act of twisting together two or more insulated components by machine to form a cable.

.Back to top
...................................................................................................................................................................
D

D-C - Direct current

D.C. - Direct current

DCR - Direct current resistance

Dielectric - An insulating material usually having a very low loss factor.

Dielectric - absorption The storage of charges within an insulation; evidenced by the decrease of current flow

after the application of dc voltage.

.Back to top
...................................................................................................................................................................
E

E - Voltage, electromotive force

Earth - British terminology for zero-reference ground.

Eddy Current - An electric current induced in a conductor by a varying magnetic field.

.Back to top
...................................................................................................................................................................
F

F - Fahrenheit

FAA - Federal Aviation Association

Fault Ground - A fault to ground.

.Back to top
...................................................................................................................................................................
G

Gage - A term used to denote the physical size of a wire.

Galvanized Steel Wire - Steel wire coated with zinc.

.Back to top
...................................................................................................................................................................
H

Hard Drawn Copper Wire - Copper wire that has been drawn to size and not annealed.

Hash Mark Stripe - A noncontinuous, helical stripe applied to a conductor for circuit identification.

Hazardous Location - Ignitable vapors, dust, or fibers that may cause fire or explosion as defined by the NEC.

Heat Distortion - Distortion or flow of a material through or configuration due to the application of heat.

Heat Shock - A test to determine stability of a material by sudden exposure to a high temperature for a short

period of time.

Hertz (Hz) - Cycles per second. A cycle that occurs once every second has a frequency of 1 hertz. The

bandwidth of the average phone line is between 300 and 3000 cycles per second.

Horizontal Stripe - A colored stripe running horizontally with the axis of a conductor, sometimes called a

longitudinal stripe, used as a means of circuit identification.

Hygroscopic - The property of a material to absorb moisture from the air.

Back to top
...................................................................................................................................................................
I

IACS - International Annealed Copper Standard

IAEI - International Association of Electrical Inspectors

ICEA - Insulated Cable Engineers Association

ICEA S-95-658-1999 - Standard for nonshielded power cables rated 2000 volts or less for the distribution of

electrical energy covers THHN/THWN, XHHW and RHH/RHW/USE cables

ID - Internal Diameter

IEEE - Institute of Electrical and Electronic Engineers

IMC - Intermediate Metal Conduit

Impedance - The ratio of the effective value of the potential difference between two terminals to the effective

value of the current flow produced by that potential difference.

Inductance - That property of an electrical circuit by virtue of which a varying current induces an electromotive

force in that circuit, or in an adjacent circuit.

Insulation - A non-conductive material usually surrounding or separating two conductive materials.

Interstice - In cable construction, the space, valley or void left between or around the cable components

IR - Insulation resistance

ISO - International Organization for Standards

Back to top
...................................................................................................................................................................
J

Jacket - A non-metallic covering over a wire insulation or an assembly of components. An overall jacket on a

multiconductor cable is also often referred to as a sheath.

Back to top
...................................................................................................................................................................
K

K - Constant used to denote insulation resistance.

CM - 1000 circular mils

ilocycle - A term denoting 1000 cycles.

Kilohertz - A term denoting one thousand cycles.

KV - 1000V

KVA - Kilovolt amperes (1000 volt x amperes).

KW - Kilowatt-1000 watts power.

KWH - Kilowatt hours (1000 watt hours).

Back to top
...................................................................................................................................................................
L 

Lay - Often referred to as pitch. The position of a helical element (conductor) of a cable in the axial length of a

turn of the helix of that element.

LS - Low smoke

Lug - A term commonly used to describe a termination, usually crimped or soldered to the conductor, with

provision for screwing down to a terminal.

Back to top
...................................................................................................................................................................
M

MCM - Thousand circular mils; e.g. 500 MCM is 500,000 circular mils.

Megohmmeter - An instrument used to measure insulation resistance (Readings are in megohmes).

Melt Extrude - To heat a material above its crystalline melt point and extrude it through an orifice.

MFT - Abbreviation for one thousand fee.t

MHO - An electrical unit of conductivity, being the conductivity of a body with the resistance of one ohm.

Mho - An electrical unit of conductivity, being the conductivity of a body with the resistance of one ohm.

MIL - Abbreviation for military as in military specification for wire or cable products.

Multi-conductor - More than one conductor within a single cable complex.

Mutual Capacitance - Capacitance between two conductors when all other conductors including ground are

connected together and then regarded as an ignored ground.

Back to top
...................................................................................................................................................................
N

NEC - National Electric Code

NEMA - National Electrical Manufacturers Association

NM - Non-metallic sheathed cable, braid or plastic covered. For dry use, 60°C.

NMC - Non-metallic sheathed cable, plastic or neoprene covered. Wet or dry use, 60°C, and corrosive

applications.

Back to top
...................................................................................................................................................................
O

OD - The overall diameter of a cable, including conductor(s), insulation(s), jacket (if used) and concentric neutral

(if used).

OEM - Original Equipment Manufacturers

OSHA - Occupational Health and Safety Administration

OSHA Occupational Safety and Health Act 1970 - Administered by U.S. Dept. of Labor which establishes

Standards and safety requirements which all businesses must meet.

Overall Diameter - The finished diameter of a wire of cable.

Overcurrent - The current which causes an excessive temperature rise in a conductor.

Overlap - The amount the trailing edge laps over the leading edge of a spiral tape wrap.

Back to top
...................................................................................................................................................................
P

Peak Voltage - The maximum instantaneous voltage.

Percent Conductivity - The conductivity of a material expressed as a percentage of that of copper.

Phase - A particular stage or point of advancement in an electrical cycle. The fractional part of the period through

which the time has advanced measured from some arbitrary point usually expressed in electrical degrees where

360° represents one cycle.

Power Cables - Cables of various sizes, construction, and insulation, single or multi-conductor, designed to

distribute primary power to various types of equipment.

Power Factor - The ratio of the power to the effective values of the electromotive force multiplied by the

effective value of current in volts and amperes respectively. The cosine of the angle between voltage applied

and the current resulting.

PSI - Pound per square inch.

PVC - Polyvinyl Chloride

Back to top
...................................................................................................................................................................

R

Rated Temperature - The maximum temperature at which an electric component can operate for extended

periods without the loss of its basic properties.

Rated Voltage - The maximum voltage at which an electrical component can be operated for extended periods

without undue degradation or safety hazard.

Reactance - That part of the impedance of an alternating current circuit which is due to capacitance or

inductance.

Resistance - The property of an electric circuit which determines for a given current the rate at which electric

energy is converted into heat and has a value such that the current squared multiplied by the resistance gives

the power converted.

RHW - Rubber-insulated building wire, heat and moisture-resistant, 75°C wet or dry locations, now allowed to

be cross-linked polyethylene insulated.

Round Wire - A wire circular in cross section as opposed to flat, square, etc.

Rupture - In the breaking strength or tensile strength tests the point at which a material physically comes apart

as opposed to yeild strength, elongation, etc.

Back to top
...................................................................................................................................................................
S

SD - Service drop cable. Two code, rubber insulated conductors, tape, laid parallel with neutral conductor

concentric thereover. Tape and braid overall. Also round construction.

SE - Above ground service entrance cable, not protected against mechanical abuse. Flame-retardant, moisture-

resistant covering. Overall neoprene sheath, 60°C-75°C.

SER - Service round entrance cable (Type SE, Style R).

Series Resistance - Any sum of resistances installed in sequential order within one circuit.

SEU - Service Entrance Cable (type SE, style U). (Unarmored).

Sheath - The material, usually an extruded plastic or elastomer, applied outermost to a wire or cable to provide

mechanical and environmental protection. Very often referred to as a jacket.

SIC - Specific inductive capacitance. Same as Dielectric Constant.

Solid Conductor - A conductor consisting of a single wire.

Spark Test - A test designed to locate pinholes in an insulated wire by application of an electrical potential

across the material for a very short period of time while the wire is drawn through an electrode field.

SPC - Submersible pump cable

Specific Gravity - The ratio of the weight of any volume of substance to a weight of an equal volume of some

substance taken as a standard, usually water for liquids and hydrogen for gases.

Square Mil - The area of a square one mil by one mil.

Strand - A single uninsulated wire.

Strand Lay - The distance of advance of one strand of a spirally stranded conductor, in one turn, measured

axially.

Stranded Conductor - A conductor composed of a group of wires, or of any combination of groups of wires.

Back to top
...................................................................................................................................................................
T

Tank Test - A term used to describe a voltage dielectric test where the specimen to be tested is submerged in a

liquid (usually water) and a voltage potential applied between the conductor and liquid as ground.

TC - Tray cable, per Art. 340 of the NEC.

Temperature Coefficient of Resistivity - The amount of resistance change of a material per degree of

temperature rise.

Tensile Strength - A term denoting the greatest longitudinal tensile stress a substance can bear without tearing

apart or rupturing.

Tensile Stress - Force per unit cross sectional area applied to elongate a material.

TFFN - Fixture wire, thermoplastic-covered with flexible stranding and nylon sheath, 90°C dry.

Thermal Rating - The maximum and /or minimum temperature at which a material will perform its functions

without undue degradation.

Thermal Resistance - That change in the electrical resistance of a material when subjected to heat. Resistance

to heat flow from conductors to outer surface of insulation or sheath in a wire of cable.

Thermal Resistivity - Thermal resistance of a unit cube of material.

Thermal Shock - The resulting characteristics when a material is subjected to rapid and wide range changes in

temperature in an effort to discover its ability to withstand heat and cold.

Thermoplastic Insulation - Jacket compounds (such as PVC, PE, and TPE) that will resoften and distort from

their formed shapes by heating above a critical temperature peculiar to the material.

Thermosetting - Term describing insulation that will resoften or distort from its formed shape by heating until a

destructive temperature is reached.

THHN - Thermoplastic insulated, high heat resistant, nylon jacketed cable, 90°C dry location, 75°C wet location.

THW - PVC insulated building wire. Flame-retardant, moisture and heat-resistant, 75°C. Dry and wet locations.

THWN - 75°C, 600V nylon jacketed PVC insulated building wire. For wet and dry locations.

THWN-2 - Same as THWN with 90°C dry, 90°C wet location.

Back to top
...................................................................................................................................................................
U

UF - Underground feeder cable, thermoplastic insulated 60°C wet or dry locations.

UFB - Underground feeder cable, thermoplastic insulated with conductors rated at 90°C.

UL - Underwriters Laboratory. Standards and tests that wire must meet in order to receive UL approval.

Ultraviolet Degradation - The degradation caused by long time exposure of a material to sunlight or other

ultraviolet rays containing radiation.

Unidirectional Stranding - A conductor stranding configuration in which all layers have the same direction of lay.

Unilay Stranding - A bunched construction having 19, 27, 37, or any number of strands which might be found in

a concentric stranding.

USE - Underground service entrance cable, rubber insulated, neoprene jacketed, 75°C wet location.

USE-2 - Same as USE except 90°C wet rating.

Back to top
...................................................................................................................................................................
V

Volt - A unit of electromotive force.

Voltage - The term most often used to designate electric pressure that exists between two points and is

capable of producing a flow of current when a closed circuit is connected between the two points.

Voltage Rating - The highest voltage that may be continuously applied to a wire or cord in conformance with

standards or specifications.

VW-1 - Underwriters Laboratories vertical wire flame test applicable to single conductor wires and cables

(formerly FR-1).

Back to top
...................................................................................................................................................................
W

W/O/G - Without ground.

Wall Thickness - A term expressing the thickness of a layer of applied insulation or jacket.

Water Absorption Test - A method to determine the water absorbed through an insulating material after a

given water immersion period.

WC 70 - Same as ICEA S-95-658-1999

WC8-1974 - Same as ICEA S68-516

Wire - Wire can be divided into two areas: 1. A slender rod or filament of drawn metal; 2. A rod of drawn metal

filament covered with insulation. These can be classified as drawn metal wire and insulated wire respectively.

Back to top
...................................................................................................................................................................
X