Fire Resisting Cable

Fire Resistant Power & Control Cables
Fire Resistant Instrumention Cables
Fire Resistant Fire Alarm Cables

Fire Resisting Cables

Fire Resistant Instrumention Cables

Braid-Screened Flexible Equipment Cables

LI-05SOZ1 FE180 (PH30) (CU/SR/OSCR/LSZH 300/500V Class 5)

Application:

The cables are designed for indoor instrumentation and control cabling, electrically noisy environments and fire

alarm systems in office buildings.

Standards:

Basic design to VDE 0812/EN 50290-2-27

VDE 0812/EN 50290-2-27

Fire Performance:

Circuit Integrity

IEC 60331-21; BS 6387 CWZ; DIN VDE 0472-814(FE180);

BS 8434-1 (30mins); BS 5839-1 Clause 26 2d; CEI 20-36/2-1; SS229-1; NBN

C 30-004 (cat. F3); NF C32-070-2.3(CR1)

Circuit Integrity with mechanical

shock

 EN 50200(PH30); CEI 20-36/4-0

Circuit Integrity with mechanical

shock & water spray

 EN 50200 annex E
System circuit integrity DIN 4102-12, E30 depending on lay system

Flame Retardance (Single Vertical

Wire Test)

EN 60332-1-2; IEC 60332-1-2; BS EN 60332-1-2;

VDE 0482-332-1 ; NBN C 30-004 (cat. F1); NF C32-070-2.1(C2);

CEI 20-35/1-2; EN 50265-2-1*; DIN VDE 0482-265-2-1*

Reduced Fire Propagation

(Vertically-mounted bundled wires

& cable test)

EN 60332-3-24 (cat. C); IEC 60332-3-24; BS EN 60332-3-24; VDE 0482-332-

3; NBN C 30-004 (cat. F2); NF C32-070-2.2(C1); CEI 20-22/3-4; EN 50266-2-

4*; DIN VDE 0482-266-2-4
Halogen Free

IEC 60754-1; EN 50267-2-1; DIN VDE 0482-267-2-1;

CEI 20-37/2-1 ; BS 6425-1*

No Corrosive Gas Emission

IEC 60754-2; EN 50267-2-2; DIN VDE 0482-267-2-2;

CEI 20-37/2-2 ; BS 6425-2*

Minimum Smoke Emission

IEC 61034-1&2; EN 61034 -1&2; DIN VDE 0482-1034-1&2;

CEI 20-37/3-1&2; EN 50268-1&2*; BS 7622-1&2*

No Toxic gases NES 02-713; NF C 20-454

Note: Asterisk * denotes superseded standard.

Cable Construction:

Conductor: Plain annealed copper wire, stranded according to IEC(EN) 60228 class 2.

Insulation: Fire resistant silicone rubber compound type EI2 as per BS 7655-1.1.

Cabling: The insulated cores are cabled in concentric layers with suitable non-hygroscopic fillers.

Fire Barrier: Polyester tape + fiber glass tape

Overall screen: Aluminum/polyester tape with tinned copper braid (min. 85% Coverage)

Outer Sheath: Thermoplastic LSZH compound type LTS3 as per BS 7655-6.1 (Thermosetting LSZH compound

type SW2-SW4 as per BS 7655-2.6 can be offered.) .

Voltage Rating:

300/500 V

Colour Code:

Insulation Colour: Per VDE 0812

Sheath Colour: Orange (other colours on request)

TYPE CODE

LI Equipment cable with fine stranded conductor

H Halogen free ceramic polymer compound C Copper Wire Braid

FE180 Insulation integrity (950°C 180 minutes)

PH 90 Fire Test for 90 mins at 830 C

Physical AND THERMAL PROPERTIES

Temperature range during operation (fixed state): -30°C – +90°C

Temperature range during installation (mobile state): -20°C – +50°C

Minimum bending radius: 7.5 x Overall Diameter

Electrical Properties:

Dielectric test:2000 V r.m.s. x 5’ (core/core)

Insulation Resistance:≥300 MΩ x km (at 20°C);

Short circuit Temperature :350°C

Construction Parameters:

Cable Code No. of Core X Cross Section Nominal Insulation Thickness Nominal Sheath Thickness Nominal Overall Diameter Approx.Weight
mm2 mm mm mm kg/km
2 cores
LI-HCH FE180 (PH30) 2x0.75 0.6 0.8 6.3 55
LI-HCH FE180 (PH30) 2x1.0 0.6 0.9 6.9 62
LI-HCH FE180 (PH30) 2x1.5 0.7 0.9 7.3 79
3 cores
LI-HCH FE180 (PH30) 3x0.75 0.6 0.8 6.6 67
LI-HCH FE180 (PH30) 3x1.0 0.6 0.9 7.2 77
LI-HCH FE180 (PH30) 3x1.5 0.7 0.9 7.6 101
4 cores
LI-HCH FE180 (PH30) 4x0.75 0.6 0.9 7.2 85
LI-HCH FE180 (PH30) 4x1.0 0.6 1.0 7.7 98
LI-HCH FE180 (PH30) 4x1.5 0.7 1.0 8.2 112
5 cores
LI-HCH FE180 (PH30) 5x0.75 0.6 0.9 7.9 105
LI-HCH FE180 (PH30) 5x1.0 0.6 1.0 7.9 117
LI-HCH FE180 (PH30) 5x1.5 0.7 1.0 9.0 127
6 cores
LI-HCH FE180 (PH30) 6x0.75 0.6 0.9 8.6 121
LI-HCH FE180 (PH30) 6x1.0 0.6 1.0 9.1 138
LI-HCH FE180 (PH30) 6x1.5 0.7 1.0 10.0 161
7 cores
LI-HCH FE180 (PH30) 7x0.75 0.6 0.9 8.6 131
LI-HCH FE180 (PH30) 7x1.0 0.6 1.0 9.1 152
LI-HCH FE180 (PH30) 7x1.5 0.7 1.1 10.0 193